UZIN KE 66
- 0.00€
Low-emission, fibre-reinforced dispersion adhesive for rubber, PVC and textile floor coverings
| Technical | |
| Purpose | Low-emission, fiber-reinforced dispersion adhesive for rubber, PVC and textile floor coverings |
| Surface | The substrate must be solid, flat, uncracked, permanently dry, clean and free of stains (remains of substances) that impair adhesion. Inspect the substrate according to applicable standards and technical sheets and immediately point out any irregularities. Vacuum the substrate thoroughly, then treat it with primer and leveling compound. Suitable primers and leveling compounds are listed in the UZIN product table. Test the substrate in accordance with the applicable standard or notices and report any deficiencies. Wait for the primer and leveling compound to dry completely. Data sheets for other products used should be considered. |
| Surface preparation | The substrate must be solid, flat, uncracked, permanently dry, clean and free of stains (remains of substances) that impair adhesion. Inspect the substrate according to applicable standards and technical sheets and immediately point out any irregularities. Vacuum the substrate thoroughly, then treat it with primer and leveling compound. Suitable primers and leveling compounds are listed in the UZIN product table. Test the substrate in accordance with the applicable standard or notices and report any deficiencies. Wait for the primer and leveling compound to dry completely. Data sheets for other products used should be considered. |
| Processing | Apply a suitable layer of adhesive to the substrate with a suitable notched trowel and wait for it to partially dry depending on the amount of application, the climate in the room, the absorbency of the substrate and the type of floor covering. Do not apply more adhesive than can be used during the working time of laying the floor covering. Lay the floor covering in a short open time and make sure that the ridge of the adhesive is pushed out. Rub or roll and weight any deformations of the floor covering. Make sure no air is trapped under the liner. Wait 20 minutes for the surface to rest, then roll it again and rub on the edges and seams. Remove the glue residue with water while it is still fresh. |
| Effect | UZIN KE 66 is a dispersion-based wet-set adhesive with a short open time and excellent adhesion. The highly shear-resistant, fiber-reinforced adhesive reduces the formation of marks on floor coverings. For internal use. |
| Usage | The shelf life is 12 months if stored in the original packaging in moderately cool conditions. Resistant to frost up to - 8 °C. Close the opened containers carefully and tightly and use the contents quickly. Allow contents to reach room temperature before use. It is best used between 18 and 25 °C, with a soil temperature above 15 °C and a relative air humidity below 65%. Low temperatures and high air humidity prolong the operating and drying time. High temperatures and low air humidity shorten the operating and drying time. Damp surfaces can cause secondary emissions and odors. Therefore, before applying the glue, make sure that the substrate is dry. Installation on a substrate with remnants of old glue can cause interactions and unpleasant odors. It is best to remove them completely. In all cases, adhesive residues must be properly treated using primers and a compound of at least 3 mm thickness. Before laying, the floor covering must be properly acclimatized to the indoor climate and without tension. Strong deformations of roll ends, hanging fields, very raised edges or strong curves must be weighted during gluing. When installing chlorine-free flooring, check the adhesive recommendations (online) or get application advice. When sealing, cleaning and maintaining the floor covering, you can use products from the UZIN Care program (UZIN Basic Cleaner, UZIN Turbo Protect Plus, UZIN Resilient Care, UZIN Refresher). See product data sheets for additional information. Follow the generally recognized rules of the profession and technology for laying floor coverings in accordance with applicable national standards (eg END, DIN, OE, SIA, etc.). The shelf life is 12 months if stored in the original packaging in moderately cool conditions. Resistant to frost up to - 8 °C. Close the opened containers carefully and tightly and use the contents quickly. Allow contents to reach room temperature before use. It is best used between 18 and 25 °C, with a soil temperature above 15 °C and a relative air humidity below 65%. Low temperatures and high air humidity prolong the operating and drying time. High temperatures and low air humidity shorten the operating and drying time. Damp surfaces can cause secondary emissions and odors. Therefore, before applying the glue, make sure that the substrate is dry. Installation on a substrate with remnants of old glue can cause interactions and unpleasant odors. It is best to remove them completely. In all cases, adhesive residues must be properly treated using primers and a compound of at least 3 mm thickness. Before laying, the floor covering must be properly acclimatized to the indoor climate and without tension. Strong deformations of roll ends, hanging fields, very raised edges or strong curves must be weighted during gluing. When installing chlorine-free flooring, check the adhesive recommendations (online) or get application advice. When sealing, cleaning and maintaining the floor covering, you can use products from the UZIN Care program (UZIN Basic Cleaner, UZIN Turbo Protect Plus, UZIN Resilient Care, UZIN Refresher). See product data sheets for additional information. Follow the generally recognized rules of the profession and technology for laying floor coverings in accordance with applicable national standards (eg END, DIN, OE, SIA, etc.). |
| Specification | short drying time excellent working properties very low consumption |
| Additional specification | The shelf life is 12 months if stored in the original packaging in moderately cool conditions. Resistant to frost up to - 8 °C. Close the opened containers carefully and tightly and use the contents quickly. Allow contents to reach room temperature before use. It is best used between 18 and 25 °C, with a soil temperature above 15 °C and a relative air humidity below 65%. Low temperatures and high air humidity prolong the operating and drying time. High temperatures and low air humidity shorten the operating and drying time. Damp surfaces can cause secondary emissions and odors. Therefore, before applying the glue, make sure that the substrate is dry. Installation on a substrate with remnants of old glue can cause interactions and unpleasant odors. It is best to remove them completely. In all cases, adhesive residues must be properly treated using primers and a compound of at least 3 mm thickness. Before laying, the floor covering must be properly acclimatized to the indoor climate and without tension. Strong deformations of roll ends, hanging fields, very raised edges or strong curves must be weighted during gluing. When installing chlorine-free flooring, check the adhesive recommendations (online) or get application advice. When sealing, cleaning and maintaining the floor covering, you can use products from the UZIN Care program (UZIN Basic Cleaner, UZIN Turbo Protect Plus, UZIN Resilient Care, UZIN Refresher). See product data sheets for additional information. Follow the generally recognized rules of the profession and technology for laying floor coverings in accordance with applicable national standards (eg END, DIN, OE, SIA, etc.). The shelf life is 12 months if stored in the original packaging in moderately cool conditions. Resistant to frost up to - 8 °C. Close the opened containers carefully and tightly and use the contents quickly. Allow contents to reach room temperature before use. It is best used between 18 and 25 °C, with a soil temperature above 15 °C and a relative air humidity below 65%. Low temperatures and high air humidity prolong the operating and drying time. High temperatures and low air humidity shorten the operating and drying time. Damp surfaces can cause secondary emissions and odors. Therefore, before applying the glue, make sure that the substrate is dry. Installation on a substrate with remnants of old glue can cause interactions and unpleasant odors. It is best to remove them completely. In all cases, adhesive residues must be properly treated using primers and a compound of at least 3 mm thickness. Before laying, the floor covering must be properly acclimatized to the indoor climate and without tension. Strong deformations of roll ends, hanging fields, very raised edges or strong curves must be weighted during gluing. When installing chlorine-free flooring, check the adhesive recommendations (online) or get application advice. When sealing, cleaning and maintaining the floor covering, you can use products from the UZIN Care program (UZIN Basic Cleaner, UZIN Turbo Protect Plus, UZIN Resilient Care, UZIN Refresher). See product data sheets for additional information. Follow the generally recognized rules of the profession and technology for laying floor coverings in accordance with applicable national standards (eg END, DIN, OE, SIA, etc.). |
| Packaging | 6 kg, 14 kg |
Recent Questions
Follow us
